Viessmann Vitosol-F Manual de servicio

Installation Instructionsfor use by heating contractorVitosol-FModels SV, SHFlat plate solar collectors for sloped roofs, flat roofsand freestanding i

Installation on Sloped Roofs10Installing the Mounting Frames (continued)Installation dimensions for ten SV collector panels6. Re-apply shingles, if re

Installation on Sloped Roofs86½” / 2200 mm7¾” / 201 mm11Installing the Mounting Frames (continued)Installation dimensions for ten SH collector panels8

Installation on Sloped Roofs12Installing the Mounting Frames (continued)Installing the mounting railsTurn the T-slot bolts 90° for allinstallation ste

Installation on Sloped Roofs13Installing the Solar CollectorsRating plate(must be on the outside of theouter collectors)Interconnecting pipes must be

Installation on Sloped Roofs14Installing the Solar Collectors (continued)7. Tighten all clamping brackets.8. Press the cover caps(partoftheconnection

Installation on Flat Roofsor Freestanding Installation15Overview of System ComponentsLegend:Collector supportCross braceAdjustable support, lower part

Installation on Flat Roofsor Freestanding Installation16Determining the Collector Row Distance “z”Legend:z=Collector row distanceh=Collector heightα=C

Installation on Flat Roofsor Freestanding Installation17Installing the Collector Supports and Adjustment of the Angle of Inclination1. Secure the lowe

Installation on Flat Roofsor Freestanding Installation18Installing Freestanding Installation (on substructures)Understructure1. Mount the understructu

Installation on Flat Roofsor Freestanding Installation19Installing Freestanding Installation (on substructures)LegendCollector connectionSpacer lip of

Safety, Installation and Warranty Requirements2Safety, Installation and Warranty RequirementsPlease ensure that these instructions are read and unders

Installation on Flat Roofsor Freestanding Installation20Installing a Freestanding Installation (with weight inserts )1. Observe the max. load and dist

Installation on Flat Roofsor Freestanding Installation21Installing Freestanding Installation (with weight inserts)6. Secure the support rails between

Installation on Flat Roofsor Freestanding Installation22Installing Freestanding Installation (with weight inserts)Collector connectionSpacer lipRating

Installation on Flat Roofsor Freestanding InstallationInstallation on Flat Roofsor Freestanding Installation23Installing Freestanding Installation (wi

Hydronic Connections24Installing the Connection Set and Collector Temperature SensorWhen assembling the locking ringcompression fitting, observe thefo

Hydronic Connections /Appendix25pCollector Supply and Return PipingH For the piping connecting thecollectors to t he Solar Diviconpumping station, Vie

Appendix26System InstallationPlease refer to the Vitosol”System Design Guidelines”for supplementary notes oninstallation examples andsystem types.H Th

Appendix27Initial Start-upCollectorPressure relief valveSolar-DiviconDiaphragm expansion vesselHigh-limit safety cut-outDHW tankAir vent c/w shut-offO

AppendixViessmann Manufacturing Company Inc.750 McMurray RoadWaterloo, Ontario • N2V 2G5 • CanadaTel. (519) 885-6300 • Fax (519) 885-0887www.viessmann

Contents3PageSafetySafety Instructions 2...Important Regulatory and Installation Requir

Contents4PageHydronic ConnectionsInstalling t he Connection Set and CollectorTemperature Sensor 24...

Safety5Important Regulatory and Installation RequirementsCodesThe installation of solar heatingsystems might be governed byindividual local rules and

General Information6About these InstructionsTake note of all symbols and notations intended to draw attention to potential hazards or important produc

General Information7Notes on InstallationH The entire solar heating sys temshould be inst alled in accordance withthe accepted rules of technology,obs

Installation on Sloped Roofs8Overview of System ComponentsSloped roof mounting hardwareRoof bracketClamping bracketJoining element f or mounting railM

Installation on Sloped Roofs9Installing the Mounting FramesInstall the panel array level or slightly inclined (approximately ½” / 10 mm) towards the c